A dovetail joint or simply dovetail is a joinery technique most commonly used in woodworking joinery (carpentry) including furniture, cabinets, carcase construction, log buildings and traditional timber framing. Noted for its resistance to being pulled apart (tensile strength), the dovetail joint is commonly used to join the sides of a drawer to the front. A series of pins cut to extend from the end of one board interlock with a series of tails cut into the end of another board. The pins and tails have a trapezoidal shape. Once glued, a wooden dovetail joint requires no mechanical fasteners.
The dovetail joint probably pre-dates written history. Some of the earliest known examples of the dovetail joint are in furniture entombed with mummies dating from First Dynasty of ancient Egypt, as well the tombs of Chinese emperors. The dovetail design is an important method of distinguishing various periods of furniture.
In Europe the dovetail joint is also called a swallow-tail joint or a fantail joint.
Video Dovetail joint
Methods
The dovetail joint is very strong because of the way the 'tails' and 'pins' are shaped. This makes it difficult to pull the joint apart and virtually impossible when glue is added. This type of joint is used in box constructions such as drawers, jewellery boxes, cabinets and other pieces of furniture where strength is required. It is a difficult joint to make manually, requiring skilled workmanship. There are different types of dovetail joints and when cut accurately they are very impressive and attractive. The joint is strong especially when used with a good quality glue such as PVA (woodworker's adhesive) or cascamite. The marking out and cutting procedure is outlined below.
The angle of slope varies according to the wood used, purpose of joint and type of work. Typically the slope is 1:6 for softwoods and a shallower 1:8 slope for hardwoods. Often a slope of 1:7 is used as a compromise. However, different slope does not affect the strength of the joint in different types of wood (hardwood and softwood) as it was reported in Woodworker Magazine.
Maps Dovetail joint
Types of dovetails
Through dovetail
The photograph at the top of this page shows a through dovetail (also known as plain dovetail) joint, where the end grain of both boards is visible when the joint is assembled. Through dovetails are common in carcass and box construction. Traditionally, the dovetails would have often been covered by a veneer. However, dovetails have become a signature of craftsmanship and are generally considered a feature, so they are rarely concealed in contemporary work. When used in drawer construction, a through (or blind, mitred, or lapped) dovetail joint is sometimes referred to as an "English dovetail."
Use for:
- Carcass and box construction
Half-blind dovetail
Craftsmen use a half-blind dovetail when they don't want the end grain visible from the front of the joint. The tails fit into mortises in the ends of the board that is the front of the item, hiding their ends.
Half-blind dovetails are commonly used to fasten drawer fronts to drawer sides. This is an alternative to the practice of attaching false fronts to drawers constructed using through dovetails.
Use for:
- Attaching drawer fronts
Secret mitred dovetail
The secret mitred dovetail joint (also called a mitred blind dovetail, full-blind dovetail, or full-blind mitred dovetail) is used in the highest class of cabinet and box work. It offers the strength found in the dovetail joint but is totally hidden from both outside faces by forming the outer edge to meet at a 45-degree angle while hiding the dovetails internally within the joint.
Use for:
- Fine cabinet or box work where strength is required without a visible joint
The mitred corner dovetail joint is very similar in design, but it has just a single dovetail and is used for picture frames and other similar joins.
Secret double-lapped dovetail
The secret double-lapped dovetail is similar to the secret mitred dovetail, but presents a very thin section of end grain on one edge of the joint.
Use for:
- Carcass and box construction to hide the dovetails completely from view
Sliding dovetail
The sliding dovetail is a method of joining two boards at right angles, where the intersection occurs within the field of one of the boards, that is not at the end. This joint provides the interlocking strength of a dovetail. Sliding dovetails are assembled by sliding the tail into the socket. It is common to slightly taper the socket, making it slightly tighter towards the rear of the joint, so that the two components can be slid together easily but the joint becomes tighter as the finished position is reached. Another method to implement a tapered sliding dovetail would be to taper the tail instead of the socket. When used in drawer construction, a "stopped sliding dovetail" that doesn't extend across the full width of the board is sometimes referred to as a "French dovetail."
Use for:
- Joining shelves to cabinet sides
- Joining cabinet bottoms to sides
- Joining horizontal partitions to shelves
- Joining adjacent sections of expandable table frames
- Joining drawer fronts to sides
- Joining front rails of web frames to cabinet sides
- Joining neck and body in violins and some guitars
Non-woodworking dovetails
Dovetails are most commonly, but not exclusively, used in woodworking. Other areas of use are:
- Dovetail slides, for example on a lathe.
- Attaching turbine blades to the shaft in jet engines and other applications.
- Clockmaking: dovetailing a new tooth, when replacing broken teeth in clock gears.
- Masonry: dovetail construction is regarded a major step forward in the design of lighthouses meant for particularly dangerous areas; the Eddystone Lighthouse and Fastnet Lighthouse are examples of the durable quality of dovetail masonry.
- 3D printing: dovetail is commonly used to overcome physical object print size limitation of a 3D printer.
See also
- Woodworking joints
References
Further reading
- Kirby, Ian J. (1999). The complete dovetail : Handmade furniture's signature joint. Bethel, CT: Cambium Press. ISBN 9780964399990.
External links
- Detailed guide from extremehowto.com
- Dovetail Joints from Manufacturer and Builder, 1869
- (Video) How to Hand Cut Precision Dovetails -- Part 1 of 2: The Pins - from woodtreks.com
Source of the article : Wikipedia
0 Comments